Category: Weight Lifting > Smith & Squat Racks

Email A Friend      Print This Page

Click to enlarge

6021 Phase Rack W/Bench

Nebula Fitness Equipment

Bench Overview: This is a totally adjustable 0-85 deg telescoping lock in bench with built in spotter stands, and a topless power cage with weight storage.

· Frame is constructed of 2.5” unist. 3x2, & 2x2 11gage (7 gage optional)

· Frame is all mig welded with steel caps welded and ground smooth over all tubing ends.

· Bench seats are actuated by (2) ½” heavy pop pins. The seat rotates off a center pivot point keeping pad gap to 1”.

· Pivot system consists of a dual heavy chrome plated arc with slotted hole pattern at every 10 deg. Backrest moves from 0-85 degrees and front from 0-30 degree.

· The bench is built with an 11/4” linear slide system actuates by a ½” pop pin. This enables the bench to telescope on itself 15” to help line bench up with the bar when locked in the rack.

· Front foot is a 11 gage box with (2) 3” hard rubber wheels built in to allow bench to telescope and be moved by the transport handle fastened to the top of the back rest frame.

· Rear frame lower 3x2 tube has (2) 3”x4”x3/4” pad screwed to it as a deck protector.

· The spotter plates are (2) 3/16”x8”x14” steel tread plates painted black bolted on the top of the frame. A 1”x Ύ” locking stud is welded to the bottom of each allowing the bench to lock into the rack spreader.

· Dimensions are L48”x W24”x H 17” Weight 130 lb

The Phase Rack:

· Rack with 48”, fits standard Olympic Power bars.

· Three (3) sets of dual system uprights. Backset of up right is 2x3 11gage tubing designated for weight storage with (5) -1 7/8” diameter plate horns per side.

· Center frame is a bolt in spreader to hold 40” spacing between the front & rear uprights. Also the safety bars store under this area out of the users way. Safety

· (1) To the rear of one of the plate trees is a tube to store (1) Olympic power bar.

· Middle uprights, (2) are designated for the squat area and are built from 3x3 7 gage tubing approx. 74”’ tall.

· Attached to the upright is the L-slot hooking system. This consists of a 3/8” x 3” Laser cut, chromed steel adjustment plate bolted to 3x3 with 3.5”x 3/8”grade 8 cap bolts. The plate has an L-shaped slot Laser cut 1 1/16” wide, and slots are 2” in depth from the horizontal inward slot. All slot bottoms are at 4” on center. L-Slot system catches then use a (2) 1” steel pin Pulse welded (a high penetration mig welding system 80,000 P.S.I. per pass) to back plate; pins protrude 3/8” to the inside to seat in the L-slot. Catch is built out of ½” plate steel formed and Pulse welded into a (3) sided locking devise. Ό” ABS plastic screwed on inside of catch for upright paint protection. Also Ό”x3” ABS plastic strip is screwed on the outside of the 3x3 as a scuff plate for the catches to avoid paint damage to rack.

· Front uprights, (2) approx. 4’ high are designated for various lifting exercises. Uprights are also fitted with matching L-slot plates facing inward toward opposing L-slots on middle uprights to enable the safety catches to be mounted to rack. Numbers stamped in the L-slots for quick adjustments.

· Front and rear uprights are not connected in the overhead position and remain open. Uprights are connected left & right side by (2) 3x2 tubes welded to stabilize the front uprights to the rest of the rack. Lower 3x2 acts as the base plate for the entire rack with Ό” x 3” x 5” lag plate with ½” hole in center welded to bottom of each end of tube. These plates allow rack to be bolted to floor.

· Uprights in the lifting area allows for overhead lift.

· Rack design and upright spacing allows for the use of the 0-85 degree (6021-B) bench in all positions with full range of movement.

· All uprights are braced and secured to each other to form a complete stable self-supporting racking system.

· Safety catches (or crash bars) are made out of 3x3 7 gage tubing 39.25” in length. A 1” steel rod 40” runs though the topside of the 3x3 and is welded at each end of the capped ends. 1” rods stick out each end 3/8” and fits into the L-slot system for mounting and adjustment. Safety has locking device, when safety is turned over while mounted in the L-slot plates, lock is engaged, it raises the safety 2” giving the user a 2” adjustment on the safety catches. Safeties will move or rotate if user hits it during the movement.

· L-slot system is self-locking and prevents attachments from coming loose, and also allows for fast easy adjustment of those attachments.

· Safety catches are approx. 39.5” in length and are covered top & bottom in Ό”x3” ABS plastic strips is screwed on to them.

· Bar Catch (or hooks) are self-locking on to the L-slot plates by way describe above.

· Hooks are removed by lifting up 2” and then pulled out in a horizontal motion to release from the L-slot plate and from around the upright. Put on in the reverse manner. Hook has a 2x2 7-gage tube pulse welded to it and then a 1.5” diameter 1018 drilled and taped rod is then welded into the 2x2. On the end id mounted a 3000 LB 1 7/8” cam follower. This acts as the catch for the Olympic power bar. The 2x2 and the 4” tall crash plate are covered in Ό” ABS plastic strips that are screwed on to them. This cam follower enables the bar to be centered on the rack with a twist and pull of the user's wrist even when bar is loaded heavy.

· Rear uprights have weight storage horns (pins) covered in plastic and accessible from the side of the rack.

· Racks have (2) sockets for Olympic bars to be stored in a vertical position at rear of the rack.

· All hooks, safety rails and plate storage pins are all covered in black ABS plastic.

· All open ends of tubing are capped in steel welded and ground smooth.

· Rack is powder coated to customer’s color specs.

· W 48” L 60” H 74” Weight 450 lb.

Average Rating: Rate it:  Poor Excellent Add to Favorites

For more information on this product, visit Nebula Fitness Equipment's website.